Bầu lọc phân tách Facet Model VCS-328-218; Coalescer model CAA28-5SB; Separator model SS618FB-5

07.09.2018 910 lượt xem

Category C Coalescer Separator housings are for commercial aviation fuel. Type S qualifications can be used at all filtration points in an aviation fueling system. Type S is meant to be used at filtration points where significant levels of water and dirt in the product can be expected. Facet VCS Series Vertical Coalescer Separator housings fully comply with EI 1581, Category C, Type S requirements.

Model VCS-328-218 ; Coalescer model CAA28-5SB; Separator model SS618FB-5

Reliable performance

Facet coalescer separators are a result of over 50 years of continuous research and development to meet the ever demanding performance requirements in the aviation fuel handling industry. This, alongwith proven field performance, demonstrates Facet’s ability to provide quality products that meet current specifications as well as specific customer requirements for installations in refineries, bulk storage terminals, heliports, airports, etc.

Standard housing design

EI 1596 Design & Construction
Welded carbon steel construction—other materials available on request
ASME Code, Section VIII construction, stamped and certified
Design pressure: 150 psi @ 250˚F—other design pressures available on request
Inlet, outlet and drain connections permanently marked
Choice of rod or screw base coalescer cartridge mounting styles
Interior: Epoxy coated (MIl-PRF-4556)
Exterior: Prime coated
Swing bolt head closures
Buna-N o-ring closure seal
Knife edge cartridge mounting seals
Headlift furnished on 18" (457 mm) OD and larger
Spider plate attached to vessel wall
Sloping cartridge plate to drain connection
4" inlet/outlet cleanout/inspection connections (when permitted by design)
Connections provided for options listed below

Options

Automatic air eliminator with check valve*
Pressure relief valve*
Differential pressure gauge*
Pilot control valve
Pilot tester
Water slug control valve
Electrical water-level alarm
Water drain valves
liquid level gauge
Blind cover for pilot control mounting flange
Immersion heaters
Sampling probes
Working platform and ladder (* Mandatory for 5th Edition)

MODEL NUMBER(1)	FLOW RATE		REQUIRED CARTRIDGES				HOUSING LIQUID VOLUME		HOUSING DRY WEIGHT		HOUSING TYPE
	AVIATION FUEL EI 1581, CATEGORY C, TYPE S		REQUIRED CARTRIDGES
	AVIATION FUEL EI 1581, CATEGORY C, TYPE S		COALESCER		SEPARATOR
	gpm	lpm	qty.	model	qty.	model	gals.	ltrs.	lbs.	kgs.
VCS-222-116	109	413	2	CAA22-5SB	1	SS616FB-5	35	132	525	238	Style B - Flat
VCS-328-218	222	840	3	CAA28-5SB	2	SS618FB-5	65	246	750	340	Style B - Flat
VCS-433-224	333	1261	4	CAA33-5SB	2	SS624FB-5	90	341	900	408	Style B - Flat
VCS-543-243	609	2305	5	CAA43-5SB	2	SS643FB-5	165	625	1200	544	Style A - Dished
VCS-556-340	782	2960	5	CAA56-5SB	3	SS640FB-5	180	681	1225	556	Style A - Dished
VCS-656-344	938	3551	6	CAA56-5SB	3	SS644FB-5	180	681	1250	567	Style A - Dished
VCS-756-440	1095	4145	7	CAA56-5SB	4	SS640FB-5	210	795	1525	692	Style A - Dished
VCS-856-444	1251	4736	8	CAA56-5SB	4	SS644FB-5	250	946	1675	760	Style A - Dished
VCS-1056-544	1564	5920	10	CAA56-5SB	5	SS644FB-5	320	1211	1875	850	Style A - Dished
VCS-1256-644	1877	7105	12	CAA56-5SB	6	SS644FB-5	385	1457	2575	1168	Style A - Dished
VCS-1356-744	2034	7700	13	CAA56-5SB	7	SS644FB-5	465	1760	2600	1179	Style A - Dished
VCS-1656-844	2500	9464	16	CAA56-5SB	8	SS644FB-5	530	2006	3000	1361	Style A - Dished

Other sizes available on request.

* Separators: If preferred, Teflon® separator cartridges can be used. Consult Factory for flow rates. The separator cartridge model number’s prefix would change from SS to ST.

Example: SS644FB-5 would change to ST644FB-5

DIMENSIONS

MODEL NUMBER(1)	inlet/ outlet diameter		main drain	dimensions(2)
	inlet/ outlet diameter		main drain	A		b		c		d		e
	in.	mm.	in.	in.	mm.	in.	mm.	in.	mm.	in.	mm.	in.	mm.
VCS-222-116	2	51	3∕4	16	406	661∕4	1683	20	508	10	254	24	610
VCS-328-218	3	76	3∕4	20	508	731∕2	1867	21	533	123∕4	324	28	711
VCS-433-224	4	102	3∕4	22	559	801∕2	2045	213∕4	552	141∕4	362	30	762
VCS-543-243	6	152	3∕4	26	660	1031∕2	2629	9	229	16	406	36	914
VCS-556-340	6	152	3∕4	26	660	1091∕2	2781	9	229	16	406	36	914
VCS-656-344	6	152	3∕4	26	660	1091∕2	2781	9	229	16	406	36	914
VCS-756-440	8	203	11∕2	28	711	1141∕4	2902	10	254	171∕2	445	45	1143
VCS-856-444	8	203	11∕2	30	762	115	2921	10	254	191∕2	495	46	1168
VCS-1056-544	8	203	11∕2	34	864	1171∕2	2985	10	254	221∕4	565	48	1219
VCS-1256-644	10	254	11∕2	36	914	1233∕4	3143	11	279	241∕4	616	55	1397
VCS-1356-744	10	254	11∕2	38	1016	1243∕4	3169	11	279	261∕2	673	56	1422
VCS-1656-844	12	305	11∕2	42	1067	1293∕4	3296	12	305	28	711	66	1676

REFERENCE NOTES:

(1) Model numbers include housing and required cartridges.

(2) Dimensions are approximate and should not be used for installation

NOTES

a. All elements are mounted against knife edge seals.

b. Nameplate to be stamped with EI classified data.

c. Inlet chamber to be hydrostatic tested at 115 psi.

d. Coalescer cartridges are offered with a choice of rod or screw base mounting. The suffix “SB” will be added to the coalescer model number when screw base is required.

Example: CAA28-5 = Rod Mount

CAA28-5SB = Screw Base

Tweet Share